How to remove kitchen faucet without basin wrench

how to remove kitchen faucet without basin wrench

how to remove kitchen faucet without basin wrench? We all know how important it is to have a clean kitchen. With so many dishes, pots and pans there’s bound to be some food on the faucet that you need to remove every once in a while.

The problem is how are we supposed to get under the sink with our hands full of dirty dishes? Well, you don’t need a basin wrench or any other type of tool for that matter!

In this article, I will show how easy it can be if you just use your dishwasher as a stepstool!

In order to use your dishwasher as a step-stool, you’ll need to have it in the “up” position and turned off.

Then grab onto one of the arms that hold up the door (usually there are two) then push down on it with all your might so that the dishwasher falls back into place.

Now just reach under and unscrew or pop out however you need to remove the faucet!

Why You Should Take the time to do this: Taking a few minutes every month or so can help prevent any pesky bacteria from forming on your faucet and make sure it stays clean for years!

Tips & Tricks: If you prefer, you could also use an old plastic bag with holes cut in two corners.

Tie one end around the arm of the dishwasher then reach under and pull up! This will give you enough space to work down there without making a mess out of things. When pulling out those dishes that are stuck at the bottom remember not to flush anything down.

Steps for how to remove kitchen faucet without basin wrench.

This content assumes that you are trying to remove a faucet without any tools. the tips shown in this article will also help you tackle other household tasks. It mentions how the best way might be with a paper towel or wetted and wrung rag. This section talks about how it will get under the handle, wiping down both sides of the spout, and then voila! The kitchen sink should be as good as new again.”

Follow these simple steps and you will be good to go.

step one:

Turn the water off. Remove handles from the faucet and unscrew bolts using a basin wrench or channel locks.

If you don’t have a basin wrench use pliers, vise-grips, or clamps to grip nuts on the inside of the pipe tightly enough that they do not spin when loosening with another tool (e.g., spanner).

Once all fasteners are removed, pull out drawers/fixtures and lift up sink flange with fingers. While pulling it away from the wall until it detaches from pipes underneath; if necessary cut through any caulk securing them together by inserting blade between the sink flange and the top of the pipes and sawing back and forth.

Step two:

Step two of how to remove kitchen faucet without basin wrench is to Insert a plastic pipe extractor into one of the openings on either side of the sink flange, then turn it counter-clockwise while pulling up with fingers until you feel resistance; keep turning the handle even if only removing a very thin layer of metal because this will prevent leaks around base later as well when replacing old fixture parts (e.g., elbows).

Pull out any remaining pieces using pliers or channel locks; use gloves so that no skin is exposed during the process! Remove aluminum foil from threads in the new package by tearing open bag at a corner just wide enough to insert the blade between layers, then pull apart with fingers and remove foil.

Step three:

 Locate the threaded hole on one side of where the old fixture was removed; insert a new piece in that opening, then use channel locks or vice-grips (depending on how far up pipe you can reach) to tighten the screw. If you cannot get a hold of how tight it needs to be, use pliers or channel locks instead; make sure the threaded end is protruding from the pipe about one inch (this will keep water pressure low). Insert another piece in the other opening and tighten screws until they are almost touching each other on both sides. Where the old fixture was removed.

Step four:

Step four of how to remove kitchen faucet without basin wrench is to Put new fixtures back onto handles. Then turn them as usual while watching for leaks around the base. If there are none this means that all connections were made correctly! Turn handle again but do not let go yet so that current does not return automatically, then hold hands under the faucet and turn on slowly.

If there are any leaks, tighten screws more until they stop leaking; if this doesn’t work the only option is to call a plumber or take it all out and start over again! 

RECENT POSTS

Conclusion:

There are a few ways to remove food from the faucet without using any tools. You can use an old toothbrush, sponge, or even a dishcloth wrapped around your hand and then dipped in soapy water. The best way is probably with a wetted and wrung paper towel or rag. All you need to do is get it under the faucet handle, wipe down both sides of the spout, and voila! Your kitchen sink should be as good as new again. What other household cleaning tasks have you tackled when relying on these tips?

Add a Comment

Your email address will not be published. Required fields are marked *